Restaurant fit out Dubai: cost, approvals and timeline
October 4, 2026 · 8 min read
A restaurant fit out in Dubai costs between AED 500 and AED 1,600 per square metre depending on the kitchen and the dining room, and runs 8 to 16 weeks from permit to handover. Crafty Clare decoration design LLC handles the turnkey scope from design and joinery to finishing, with the joinery built in our own workshop in Jebel Ali.
Turnkey restaurant fit out Dubai: one contract from design to handover
A turnkey restaurant fit out in Dubai puts design, joinery production, site works and finishing under one contract, so you deal with one team from first drawing to handover. We build the bar counters, banquettes and wall panelling in our Jebel Ali joinery workshop and coordinate the kitchen, MEP and finishing trades on site.
That single scope matters most when the kitchen equipment, grease route and front-of-house joinery have to land in the same programme. The equipment installer, the MEP team and our finishers are sequenced rather than booked into the same week. If you already have a floor plan, bring it to the first meeting. We will price the fit out against the real kitchen layout, not a generic rate.
Why work with Crafty Clare decoration design LLC
- Turnkey interiors: design, joinery and finishing under one contract
- Own joinery workshop in Jebel Ali
- Commercial F&B focus: cafes, restaurants and cloud kitchens
- Joinery built in-house, not outsourced
- Serving Jebel Ali and the wider Dubai market
- Direct WhatsApp line on 050 857 0938
What an F&B fit-out covers
A commercial fit out covers the kitchen shell, the grease line, front-of-house joinery, bar counters, feature ceilings and walls, washrooms and signage. The joinery is the part we build ourselves in Jebel Ali, and the rest is coordinated so the equipment installer, the MEP team and the finishers are not booked into the same week.
- Kitchen shell: grease duct route, extract hoods, floor falls, drainage, cold room panels, three-phase power
- Ventilation: hood, duct, extract fan, make-up air and the discharge point agreed with the landlord
- Front of house: bar counter, back bar, banquettes, host station, waiter stations, wall panelling
- Feature ceilings and walls: bulkheads, acoustic panels, decorative plaster, slatted timber
- Washrooms: vanity joinery, mirrors, tiling and accessible cubicle set-out
- Signage and shopfront: DET-compliant signage, glazing, thresholds and door hardware
Every item on that list is drawn into one coordinated set before a board is cut. Our restaurant fit out in Dubai service page breaks the scope down further.
Restaurant fit out cost Dubai: what to budget per square metre
Budget AED 500 to 900 per square metre for a cafe with a light prep kitchen, and AED 900 to 1,600 per square metre for a full restaurant with a commercial kitchen and seated dining. Those bands cover building works and finishes. Kitchen equipment, loose furniture and DET fees sit outside them.
| Format | Rate per sqm | Main drivers |
|---|---|---|
| Cafe, 60 to 120 sqm | AED 500 to 900 | Espresso bar, display counter, seating |
| Restaurant, 150 to 400 sqm | AED 900 to 1,600 | Grease line, cold room, dining joinery |
| Cloud kitchen unit | AED 600 to 1,000 | Extraction route, drainage, washable finishes |
Worked example. A 150 sqm cafe in a Jebel Ali retail unit with a 20 sqm prep area, 55 covers and a full front-of-house joinery package usually lands between AED 110,000 and AED 180,000 for building works. Bar counter, banquettes and display joinery add AED 45,000 to AED 90,000. The same footprint as a full restaurant with a commercial kitchen moves to AED 250,000 to AED 400,000.
The grease route is the biggest single variable. A duct that crosses a mall ceiling void or runs up an outside wall can add AED 20,000 to AED 60,000 in steel, fire stopping and landlord supervision. Our cafe and restaurant fit-out projects show how those routes were resolved.

Teal velvet seating under a crystal chandelier, with gold trim and marble underfoot. Feature moments like this come out of our Jebel Ali joinery workshop.
Approvals: DET, Dubai Municipality food control and civil defence
You need a DET trade licence for the activity, Dubai Municipality food control approval for the kitchen layout, and civil defence sign-off before you can open. Delays in approvals push back more openings than site work does.
DET trade licence. The licensed activity has to match what you sell. A cafe licence does not cover a full restaurant menu, and the submitted layout is checked against the licence.
Dubai Municipality food control. The kitchen is assessed on workflow, handwash basins, separate raw and cooked zones, cold storage temperatures and waste handling. Staff complete food safety training through Food Watch, and the extraction system is checked at the opening inspection.
Civil defence. Means of escape, fire-rated partitions, hood suppression, extinguishers and exit signage are reviewed together. A hood without a suppression system stops the inspection.
Ventilation, noise and landlord rules. The extract discharge point, make-up air volume and boundary noise levels are reviewed. Mall landlords want drawings through their own consultant and hold a fit-out deposit until snagging closes. Street-side units give more freedom on the shopfront but leave you carrying the grease trap and odour control.
Programme and sequencing for an 8 to 16 week fit out
A cafe runs 8 to 12 weeks from permit to handover and a full restaurant runs 12 to 16 weeks. Imported kitchen equipment takes 6 to 10 weeks to arrive, so the order goes in during week one.
- Weeks 1 to 3. Design, kitchen equipment schedule and layout freeze.
- Weeks 2 to 4. Joinery production starts in the Jebel Ali workshop, with bars and counters dry-fitted before they reach site.
- Weeks 3 to 8. Permit submissions run in parallel with the build, not before it.
- Weeks 5 to 9. Demolition, MEP first fix, grease duct installation and pressure testing.
- Weeks 8 to 12. Kitchen equipment setting, extraction commissioning and cold room installation.
- Weeks 10 to 14. Front-of-house joinery, banquettes, ceilings, tiling and paint.
- Weeks 14 to 16. Load testing, food control inspection, snagging and handover.
Building custom joinery for bars and counters in our own workshop is what makes that overlap possible.
Fit-out choices that cut long-term maintenance
Material choices made in week two decide how many service calls you take in year four. Dubai humidity, grease and cooling loads punish the wrong specification quickly.
- Stainless steel or powder-coated aluminium for shopfront and kitchen-adjacent framing
- Epoxy grout in wet areas and back of house instead of cement grout
- Porcelain or commercial vinyl in the dining area instead of laminate
- Compact laminate bar tops instead of sealed timber
- LED strip set into aluminium channels with removable diffusers
- Access panels on the grease duct and above the bar
- Powder-coated metalwork and porcelain paving outside, where cheaper paint lifts within a season

Gatework, stone mosaic paving and planting on a finished exterior. Outdoor finishes have to survive Dubai heat and dust with little upkeep.
Handover, snagging and opening day
Handover should include as-built drawings, O&M manuals, equipment warranties and a snag list closed within 14 days. Missing documents cost you on the first breakdown.
Walk the job with the operations team and test under real load. Run the extract at full speed, run the dishwash and the cold room overnight, check door closers, thresholds and grease trap access, and confirm every door and drawer still lines up after a week on site. Leave 5 to 7 days between snag close and first service so staff training does not collide with final touches. When you are ready to price a job, book an F&B fit-out consultation and bring the floor plan.
Frequently asked questions
How much does a restaurant fit out cost in Dubai?
A cafe with a light kitchen usually costs AED 500 to 900 per square metre and a full restaurant costs AED 900 to 1,600 per square metre. A 150 sqm cafe typically lands between AED 110,000 and AED 180,000 for building works, with bar counter and banquette joinery quoted separately.
What does a turnkey restaurant fit out in Dubai include?
A turnkey restaurant fit out in Dubai includes design, joinery production, site works, MEP coordination, finishes and handover under one contract. Crafty Clare builds bar counters, banquettes and wall panelling in our Jebel Ali workshop and sequences the kitchen equipment and finishing trades on site.
How long does an F&B fit out take from design to handover?
Allow 8 to 12 weeks for a cafe and 12 to 16 weeks for a full restaurant. Permits run in parallel with the build, so ordering kitchen equipment in week one is what protects the handover date. Imported items can take 6 to 10 weeks to reach Dubai.
Which approvals do I need before opening a cafe or restaurant in Dubai?
You need a DET trade licence for the right activity, Dubai Municipality food control approval for the kitchen layout, Food Watch training for staff, and civil defence sign-off on fire safety and hood suppression. Ventilation, noise and landlord approvals sit alongside those.
Do you build bar counters and front-of-house joinery in your own workshop?
Yes. Bar counters, back bars, banquettes, host stations and wall panelling are produced in our joinery workshop in Jebel Ali. Building in-house means the counter can be dry-fitted and adjusted before the floor screed is finished.
What is included at handover and how long does snagging take?
Handover includes as-built drawings, O&M manuals, equipment warranties and a snag list closed within 14 days. Extraction, cold room and dishwash are tested under real load before sign-off, and 5 to 7 days should sit between snag close and first service.
Planning a project in Dubai?
Tell us about your space and we'll come back with a plan and a price.
Get A QuoteWhatsApp Us

